Search found 13 matches
- Thu Mar 16, 2023 4:38 pm
- Forum: Training Discussion
- Topic: Swapping long videos
- Replies: 3
- Views: 1954
Re: Swapping long videos
Thank you for the reply. Are there any negative repercussions or hard limits of how many images to with at one time (50,000-500,000 faces)? I remember the FAQ recommending 500-5,000 faces per side. I was concerned about trying to train with 10-100x the number. When a new season of a show is released...
- Thu Mar 16, 2023 8:54 am
- Forum: Training Discussion
- Topic: Swapping long videos
- Replies: 3
- Views: 1954
Swapping long videos
If swapping the same A and B a 30 minute show... or an entire season of 30 minute shows, should I reuse a single model, or create multiple models? Would each episode have to be split into smaller scenes (assuming 50k+ A-Faces per episode), or just trained all at the same time? If using the same mode...
- Sat Feb 25, 2023 4:59 pm
- Forum: Training Support
- Topic: Training speed tapers off after a two minutes
- Replies: 4
- Views: 1312
Re: Training speed tapers off after a two minutes
Problem solved. The low/tapering performance was caused by using vgg-clear for the training mask. After switching to bisenet-fp, performance has gone back up to 110 eg/s (sustained over 14 hours so far).
- Wed Feb 22, 2023 3:12 am
- Forum: Training Support
- Topic: Training speed tapers off after a two minutes
- Replies: 4
- Views: 1312
Re: Training speed tapers off after a two minutes
Thanks for the reply. The fact that this might be indicative of a bottleneck gives me a place to start. Hardware wise, I'm running a relatively new i7-12700k with 32GB of DDR4 3600 memory. CPU utilization itself is low, running about 14% during training, but I'm not sure about memory bandwidth. I wo...
- Tue Feb 21, 2023 7:45 pm
- Forum: Training Support
- Topic: Training speed tapers off after a two minutes
- Replies: 4
- Views: 1312
Training speed tapers off after a two minutes
Lately I've been having an issue with training performance that I'm struggling to isolate. Training (DNY256 batch-26) starts out strong @ 100 eg/s, but after ~ 2 minutes, the speed starts gradually decreasing to about 55-60 eg/s, where it will stay permanently. Along with the performance drop, GPU p...
- Mon Dec 12, 2022 5:38 pm
- Forum: Hardware
- Topic: Hardware best practices
- Replies: 83
- Views: 183577
Re: Hardware best practices
GPU prices are still fluctuating quite a bit, but in my area, the 3090ti is hovering around the same price as the 4080 16GB. Would you recommend the 4080 over 3090ti?
- Sat Dec 10, 2022 2:41 am
- Forum: Hardware
- Topic: Hardware best practices
- Replies: 83
- Views: 183577
Re: Hardware best practices
Thank you for the reply. How are the RAM temps on your 3090? I read that VRAM intensive applications (e.g., ETH mining) caused dangerous temperature (>100 C memory junction temperature) levels on many 3090s, and required additional cooling to the back of the card. I wonder if FS has a similar type o...
- Fri Dec 09, 2022 5:15 pm
- Forum: Hardware
- Topic: Hardware best practices
- Replies: 83
- Views: 183577
Re: Hardware best practices
A few GPU questions:
-
Are the new 40xx GPUs automatically supported by Faceswap, or is an update required?
-
Do faceswap workloads cause concerning memory temperatures on the 3090 (as they do with crypto mining)?
-
How would the 4080 16GB would stack up against the 3090 or 3090ti?
- Fri Nov 18, 2022 5:56 pm
- Forum: Training Support
- Topic: Gray outline around edge of converted face - Phaze-a DNY256 preset
- Replies: 7
- Views: 1361
Re: Gray outline around edge of converted face - Phaze-a DNY256 preset
I have confirmed Phaze A with DFL SAE preset (loaded from model_phaze_a_dfl-sae-df_preset.json) behaves the same as the standalone DFL SAE model; the edges look good.
Let me know if there are any other tests I can run to help.
- Fri Nov 18, 2022 2:00 am
- Forum: Training Support
- Topic: Gray outline around edge of converted face - Phaze-a DNY256 preset
- Replies: 7
- Views: 1361
Re: Gray outline around edge of converted face - Phaze-a DNY256 preset
No - It was the standalone model of DFL-SAE.
I will now run a test of Phaze A + DFL SAE Preset though with the same data and settings to compare the three.
- Wed Nov 16, 2022 10:30 pm
- Forum: Training Support
- Topic: Gray outline around edge of converted face - Phaze-a DNY256 preset
- Replies: 7
- Views: 1361
Re: Gray outline around edge of converted face - Phaze-a DNY256 preset
I'll check out that thread, thanks. A and B data sets are identical. Starting with default DFL-SAE and DNY256 presets, I changed a few global options, but for both models: Train-Global-Network-Mixed Precision: True Train-Global-Loss-Mask: Vgg-clear Train-Model-Dfl Sae: (No changes) Train-Model-Phaze...
- Tue Nov 15, 2022 9:53 pm
- Forum: Training Support
- Topic: Gray outline around edge of converted face - Phaze-a DNY256 preset
- Replies: 7
- Views: 1361
Re: Gray outline around edge of converted face - Phaze-a DNY256 preset
Here is a comparison between DNY256 (200k it) and DFL-SAE (30k it)
- Sun Nov 13, 2022 7:07 am
- Forum: Training Support
- Topic: Gray outline around edge of converted face - Phaze-a DNY256 preset
- Replies: 7
- Views: 1361
Gray outline around edge of converted face - Phaze-a DNY256 preset
When using Phaze-a with the DNY256 preset, I am getting a gray outline around the converted face, usually on the top and sides. The swap otherwise looks amazing. The issue does not appear when using the same A/B data with DFL-SAE. I tried using Reflect Padding with Phaze-A/DNY256, but then model doe...