Nvidia-SMI reports the Cuda version that your GPU driver supports. Not the version that is installed. It is, however, not at all obvious that this is the case
Search found 2638 matches
- Wed Mar 27, 2024 2:05 pm
- Forum: Installation Support
- Topic: Feedback to an old issue.
- Replies: 2
- Views: 71
- Tue Mar 26, 2024 2:22 pm
- Forum: Extract Support
- Topic: Config parameters from command line
- Replies: 2
- Views: 86
Re: Config parameters from command line
- Tue Mar 26, 2024 2:20 pm
- Forum: Training Support
- Topic: Training with Original trainer: after 35+ k iterations only the 1st A and 1st B images are showing
- Replies: 3
- Views: 122
Re: Training with Original trainer: after 35+ k iterations only the 1st A and 1st B images are showing
A screengrab would make this easier... But it should start resembling faces fairly quickly (within a save iteration or 2). If it isn't, then the model has collapsed and you'll most likely need to start again with a lower learning rate.
- Sun Mar 24, 2024 7:54 pm
- Forum: Training Support
- Topic: Training with Original trainer: after 35+ k iterations only the 1st A and 1st B images are showing
- Replies: 3
- Views: 122
Re: Training with Original trainer: after 35+ k iterations only the 1st A and 1st B images are showing
- Sun Mar 24, 2024 7:51 pm
- Forum: Training Discussion
- Topic: Teeth
- Replies: 3
- Views: 453
Re: Teeth
I can't say I have had this issue.
You could try just adjusting the weight of LPIPS down, rather than disabling it altogether.
- Sun Mar 24, 2024 7:50 pm
- Forum: Training Support
- Topic: Is this training going well?
- Replies: 1
- Views: 102
- Sun Mar 24, 2024 7:50 pm
- Forum: Training Support
- Topic: A newbie question: Is it possible to partially re-use an already trained model if you decide to swap the person A?
- Replies: 1
- Views: 64
Re: A newbie question: Is it possible to partially re-use an already trained model if you decide to swap the person A?
- Fri Mar 22, 2024 12:15 pm
- Forum: Training Support
- Topic: Training error
- Replies: 3
- Views: 3830
- Fri Mar 22, 2024 12:43 am
- Forum: Installation Support
- Topic: [Guide] macOS Install Guide: Installer Method
- Replies: 33
- Views: 67388
Re: [Guide] macOS Install Guide: Installer Method
Unfortunately there is not enough information in that error message to know what the issue is.
Most likely you are missing one of the pre-requisites
- Fri Mar 22, 2024 12:40 am
- Forum: Training Support
- Topic: ERROR Caught exception in thread: '_training'
- Replies: 1
- Views: 329
Re: ERROR Caught exception in thread: '_training'
- Thu Mar 21, 2024 11:57 am
- Forum: Installation Support
- Topic: I have been stuck in this position and cannot install successfully. How can I solve it?
- Replies: 1
- Views: 341
Re: I have been stuck in this position and cannot install successfully. How can I solve it?
There was a bug which prevented the installer from running.
I have just pushed a fix for this, so please try running the installer again (no need to re-download it).
- Wed Mar 20, 2024 12:36 pm
- Forum: Training Support
- Topic: bugs on training
- Replies: 3
- Views: 382
Re: bugs on training
- Tue Mar 19, 2024 4:07 pm
- Forum: Training Support
- Topic: Help! Unknown: CUDNN_STATUS_EXECUTION_FAILED Error out of the blue after PC crashed. Reinstall won't Fix
- Replies: 1
- Views: 284
Re: Help! Unknown: CUDNN_STATUS_EXECUTION_FAILED Error out of the blue after PC crashed. Reinstall won't Fix
- Tue Mar 19, 2024 4:04 pm
- Forum: Training Support
- Topic: bugs on training
- Replies: 3
- Views: 382
Re: bugs on training
- Tue Mar 19, 2024 4:01 pm
- Forum: Training Support
- Topic: Preview only shows mask? Phaze-A, maskers: Bisect-Fp + Vgg-Clear + VggObstructed
- Replies: 6
- Views: 3866
Re: Preview only shows mask? Phaze-A, maskers: Bisect-Fp + Vgg-Clear + VggObstructed
Most likely you will need to delete your model, lower the learning rate (try 3.5e-5, if that doesn't work, then 1e-5) and start again.
- Wed Mar 13, 2024 11:36 pm
- Forum: Convert Support
- Topic: help!
- Replies: 1
- Views: 373
Re: help!
Most likely one or both of:
- D:/faceswap/A/faceimagesA
- D:/faceswap/B/faceimagesB
does not contain faceswap extracted facesets. All images in these folders must be face images that have been extracted by faceswap
- Wed Mar 13, 2024 11:30 pm
- Forum: Installation Support
- Topic: Debian Installation does not work?
- Replies: 1
- Views: 353
Re: Debian Installation does not work?
What do you mean nothing works?
Try:
Code: Select all
conda activate faceswap
cd faceswap
python faceswap.py gui
Post any error output
- Wed Mar 13, 2024 11:27 pm
- Forum: Convert Support
- Topic: convert process is failed in the middle
- Replies: 1
- Views: 272
Re: convert process is failed in the middle
- Wed Mar 13, 2024 11:25 pm
- Forum: Training Discussion
- Topic: Teeth
- Replies: 3
- Views: 453
Re: Teeth
- Wed Mar 13, 2024 11:23 pm
- Forum: Training Discussion
- Topic: difference between left & right eye
- Replies: 1
- Views: 333
Re: difference between left & right eye
I can honestly say I've never seen this issue. I've had models where eye-tracking has gone wonky, but not your specific example.